Allow the Dash Mount adhesive to cure dry for a minimum of hours before using the mount. If the vent louvers in your vehicle Short Vent are recessed, you may need to use Clamps the longer vent clamps with the Vent Mount. Push the Vent Mount onto the vehicle vent as shown 1 until it hooks on the rear of the vent louver 2. Rest the foot against the bottom of the vent 2 , and adjust the tilt of the Vent Mount by repositioning the foot to a different adjustment hole 3. To install the Magnetic Mount Antenna: Choose the best location for your antenna considering your own personal situation.
Page 23 SUV: We recommend mounting the antenna at the rear of the roof as shown. Convertible: We recommend mounting the antenna at the leading edge of the trunk as shown. Pickup Truck: We recommend mounting the antenna above the front windshield as shown. The Rubber Tail will help to position the antenna the correct distance from the edge of the roof or trunk lid.
Page 25 TIP! Mount the antenna on the roof for most vehicles or trunk for convertibles where it has a clear view of the sky in all directions.
Mount the antenna on the roof where it has at least 3 inches of clear space around it. Use the supplied Rubber Tail to cover and protect the antenna cable. Mount it at least 3 inches away. Always be careful to include enough slack in your cable to accommodate open doors or trunk lids. Use things typically found around the home, like electrical tape, to secure cables in areas so that hinges do not pinch the cable with the door. Use a blunt plastic putty knife, a credit card, a plastic knife, or a similar blunt tool to lift the rubber window moulding Page 30 Vehicle Installation Route cable out from under rear windshield moulding and tuck into weatherstripping around trunk opening Avoid sharp bends by running cable through weatherstripping for several inches Pull weatherstripping from trunk opening Tuck cable into weather- stripping.
Route cable through weatherstripping several inches to avoid sharp bends Pull cable out of weather Page 31 Bring cable out of weatherstripping and into trunk Route cable along trunk wall and into cabin through gap or conduit, along existing wiring harness Route cable along trunk wall and into cabin Page 32 Vehicle Installation Use a blunt plastic putty knife or similar blunt tool trim and tuck cable under trim.
Continue Route cable under towards front of vehicle trim or upholstery Continue routing cable under trim or carpet towards front of vehicle Route cable from trunk under interior trim, into cabin and towards front Page 33 Continue routing cable under carpet or console to radio location Coil excess cable under Pull carpet carpet or mat or mat back Bring cable out from trim Bring cable out from trim and route under carpet to dashboard or console TIP!
Feed the antenna cable from the antenna underneath the rubber molding around the rear window. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the rear window and tuck the antenna cable underneath the molding.
Page 35 area under the interior trim, towards the front of the vehicle. Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath.
Avoid side airbag locations on back pillars and above the doors. Feed the antenna cable from the antenna underneath the rubber molding around the windshield. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath the molding.
Page 37 SUV: 1. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. Secure the excess cable with wire ties purchased separately. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you can easily connect it to the antenna connector of the dock. Be careful not to crimp or cut the cable. Bring the cable out from the trim near the front of the cabin and route it under the carpet toward the dashboard or console.
Coil any excess cable in a hidden location, such as under the carpet, keeping it away from any vehicle pedals or controls. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the windshield and tuck the antenna cable underneath it. Continue tucking the cable underneath the windshield molding around the windshield to the lowest corner. Page Step 6: Connect The Audio Cassette Adapters are sold separately and can be purchased from an electronics retailer, or go to sirius.
Insert your Starmate 5 into the dock, aligning the radio against the rear of the dock so that the rails on the dock fit into the mounting Page 44 Ensure that the Starmate 5 is tuned to channel Also be sure that the audio level is set high enough to be heard step 9. Page 46 Insert your Starmate 5 into the dock, aligning the radio against the rear of the dock so that the rails on the dock fit into the mounting slots in the back of the radio.
Set it to play input from the cassette source. You are now ready to activate your Starmate 5. Page 48 Vehicle Installation The audio level output of the Starmate 5 can be increased or decreased as necessary to match the audio levels of other sources in your vehicle.
Page 49 Option 3: PowerConnect Installation Instructions Insert your Starmate 5 into the dock, aligning the radio against the rear of the dock so that the rails on the dock fit into the mounting slots in the back of the radio. Power on Starmate 5 radio by pressing the Power button. Page 50 FM radio station. Write down each FM channel that has only static or silence on it, until you reach Ensure that the Starmate 5 is tuned to channel Page 51 FM radio if you have not already done so and tune it to this FM channel.
Press menu. To learn more, check with the retailer where you bought your radio, or go to sirius. Wait until any channel updates have completed before pressing any buttons.
Page 57 When your service is activated, your Starmate 5 will display an alert message. To continue, press any button. Thereafter, if you press the Up or Down button you can scroll and tune other channels. Activation usually takes less than 5 minutes, but sometimes may take longer.
Repeated momentary pressing and releasing of disp will sequence the display between listings of artist names, song titles, and back to channel names. What is the difference between FM and AM? The biggest difference between FM radio stations compared to AM radio stations is the sound quality.
When is my volume too loud? A volume above 80 decibels can be harmful to hearing. When the volume exceeds decibels, direct damage can even occur. The chance of hearing damage depends on the listening frequency and duration. How can I best clean my Radio? No, Thanks. Subscription Activation. Activation Fee: For each Receiver on your account, we may charge you a fee to activate, reactivate, upgrade or modify your Service. The fee is payable with your first subscription fee payment.
For weather data Service, the activation fees can be found in our Customer Agreement. Subscription Royalty. Music Royalty Fee. For further details on how this fee is calculated see FAQs. Subscription Tax. Taxes: You are responsible for all taxes or other government fees and charges, if any, which are assessed based on the Service address on your account.
All amounts charged to your account, including fees and shipping charges for Receivers purchased directly from the Site, may be subject to tax, which will vary according to your billing or shipping address and applicable law. System Power Requirements:. Get SiriusXM. Manage My Account.
0コメント